ps4-skins-5fa249d30bb50

  • BANBLUE 50 Amp Power Inlet Box, NEMA SS 2-50P, 125/250 Volt Generator Inlet, for Generators Up to 12,500 Watts, Weatherproof, Outdoor Use, ETL Listed
    Configuration: ETL LISTED, 50A, 125/250V, 12500W Generator Power Inlet Box, NEMA CS6375 or SS2-50P inlet plug, compatible with all 50 Amp NEMA SS2-50P generator cord. This power inlet box is an outdoor/watertight electrical inlet. To prevent dangerous carbon monoxide fumes from the generator from entering your house. Then it will be safely hardwired through an outside wall directly to the transfer switch or panel, eliminating the need for cords running through windows or doors. Power on indication: Upgraded with the Green Light Power on Indication on the lid, will light on when plug in and start power connection. Comparing with old version, this power inlet box is more visible and safer when working, especially at night or dark area. 1.2" knockouts on 4 areas (Left, Right, Bottom & Back) could connect to transfer switch and electric panel on multi-directions straightly. No more serious curving wire. The whole metal body is covered by anti-rust powder coating and the fliping cap could be shut down when it is not working in order to prevent dust, humid air and water.
  • BA-2R62-P5 Basic Switch Snap Action 20 A, 125, 250 Or 480 VAC T79399
    2 Year Warranty
  • Parallax Power Supply  (ATS501 120/240 Volt 50 Amp Transfer Switch
    Parallax Power Supply Line Generator Switch Model ATS 501 With a flick of the generator switch, the ATS 501 line generator switch from Parallax transfers power smoothly between shoreline power and generator/secondary power source, regardless of line voltage conditions ATS 501 is engineered for superior reliability in 50 Amp, 120/240-volt electrical systems (per the new UL Standard 1008) Electronic circuit board design is proven in extensive cycle testing to withstand heat and torque The low-profile chassis measuring just 3-1/2 high allows mounting in areas not possible with other 50 Amp transfer switches, and installation can be made without cover removal
  • SmartPlug 30 Amp 50ft Cordset w/Stainless Steel Inlet & No Thermostat , small -C30503/BM30NT
    Eliminates overheating - increased pin & clip surface area greatly improves electrical conductivity during high amperage demand Ease of Use - no twist required, the unique plug body shape and push-in design means it only goes in the right way every time - even in the dark Multi-point locking System - side clips and Inlet cover lock the plug body securely into the Inlet which eliminates any stress from movement of the power cord Weatherproof seals - multi-fin silicone gaskets installed in the interior of the plug body eliminate any water penetration when plug is connected to Inlet 125 Volt / 250 Volt . Blue LED power indicator light - Cordset has two blue LEDs to increase visibility Quick and Easy Installation- Inlet mounting flange holes match twist-type holes for an installation that is typically finished in 30 minutes- the total install takes less than 60 minutes
  • GPI Replacement Switch Assembly for M-150S Fuel Transfer Pumps, Switch, Breaker, Bracket (GPI Genuine Accessory 110277-505)
    This Switch Assembly comes with a switch, breaker and bracket that is compatible with all GPI M-150S fuel pumps. Quick and easy installation to get your pump back up and running. GPI Genuine Parts & Accessories are tested and approved for use with GPI fuel transfer pumps and are backed by a 90 day limited manufacturer’s warranty Made in the USA.
  • Gikfun DIY 5A Range AC Current Transformer Module for Arduino (Pack of 5pcs) EK1344x5
    It's diy kits, need to solder by yourself onboard precision micro current transformer the module can measure AC currents less than 5A, the corresponding analog output 5A/5mA Pack of 5pcs 80 Ohm resistor
  • Conntek 80601-GYBX 30 Amps 125/250 Volts Power Inlet Box, For Generators Up to 7,500 Watts, Grey Cap
    Configuration: NEMA L14-30P (30 Amps, 125/250 Volts) For Use With Generators Up to 7,500 Running Watts 4 Combination 1/2” & ¾” knockouts Grey Cap for Additional Personalization Recommended Cord Sets: TE-20601 or Any Variation of 20601
  • Baomain Circuit breaker Thermal overload switch protector W66-30A 125/250VAC/50VDC Push Button Reset-Only CLB with Quick Connect Terminals
    Rating: 30A 125/250VAC/50VDC terminal width: 6.3mm(1/4") Screw hole dia: 10.8mm Body size: 35.5mm x 14.8mm UL CSA TüV RoHS listed
  • K177-1015 | KB Electronics Solid State Variable Speed AC Electric Motor Control 15.0 Max amps 115V
    Designed for Standard 4" x 4" Electrical Wall Box 15.0 Max amps 115 Volts; UL & CSA Approved Not to be used with Capacitor Start or Capacitor Run Motors Applications: Fans, Blowers, Fireplace Blowers, Attic Fans, Humidifiers, Ventilators
  • K177-1005 | KB Electronics Solid State Variable Speed AC Electric Motor Control 5.0 Max amps 115V
    Designed for Standard 2" x 4" Electrical Wall Box 5.0 Max amps 115 Volts; UL & CSA Approved Not to be used with Capacitor Start or Capacitor Run Motors Applications: Fans, Blowers, Fireplace Blowers, Attic Fans, Humidifiers, Ventilators
This site uses cookies: Accept / Deny